Plastic tubes semi-rigid - flexible
PA 12 HL, PA 12 PHL

Plastic tubes flexible Plastic tubes semi-rigid
Plastic tubes flexible Plastic tubes semi-rigid
 
 
 

Plastic tubes / nylon tubings semi rigid PA 12 HL


DIN 73378


Operative pressure for Ø 4 x 0,85 and 23°C: approx. 1044 PSI / 7 MPA / 72 bar

Operative pressure for Ø 6 x 1,25 and 23°C: approx. 1015 PSI / 7 MPA / 70 bar 

Operative pressure for Ø 6 x 1,5 and 23°C: approx. 1291 PSI / 9 MPA / 89 bar       

Item No. Color Material Dimension Grease D D1 S m / coil Box Palett
100-010 black PA 12 HL 4 x 0,85 unfilled 4 2,3 0,85 50 1500 5000
100-010-T transparent PA 12 HL 4 x 0,85 unfilled 4 2,3 0,85 50 1500 5000
4511-100 black PA 12 HL 4 x 0,85 NLGI class 000 4 2,3 0,85 50 1500 5000
100-009-25 black PA 12 HL 6 x 1,5 NLGI class 2 6 3,0 1,5 25 750 4000
100-004 black PA 12 HL 6 x 1,5 NLGI class 000 6 3,0 1,5 100 500 4000
100-003-25 black PA 12 HL 6 x 1,5 unfilled 6 3,0 1,5 25 750 4000
100-003 black PA 12 HL 6 x 1,5 unfilled 6 3,0 1,5 100 500 4000
4510-001 transparent PA 12 HL 6 x 1,25 unfilled 6 3,5 1,25 100 500 4000


_____________________________________________________________________________________________________


Plastic tubes / nylon tubings flexible PA 12 PHL

DIN 73378

Operating pressure: 

100-005 / 100-006 approx. 39 bar / 570 PSI / 4 MPA 

100-006-T approx. 36 bar / 522 PSI / 3,6 MPA

100-007 approx. 44 bar / 640 PSI / 4,4 MPA

Item No. Color Material Dimension Grease D D1 S m / coil Box Palett
100-005 black PA 12 PHL 4 x 0,85 NLGI class 000 4 2,3 0,85 50 1500 5000
100-006 black PA 12 PHL 4 x 0,85 unfilled 4 2,3 0,85 50 1500 5000
100-006-T transparent PA 12 PHL 4 x 0,85 unfilled 4 2,3 0,85 50 1500 5000
100-007 black PA 12 PHL 6 x 1,5 unfilled 6 3,0 1,5 100 500 4000
4513-100 black PA 12 PHL 6 x 1,5 NGLI 000 6 3,0 1,5 100 500 4000

Our plastic tubes / tube lines are used in lubrication systems to connect the progressive distribution unit with the lubrication point or the relubrication distributor (or piston distributor) to the lubrication point.


Mounting advise:

Please do always use reinforcing sockets for plastic tubes with diameter  4x 0,85 and 6x1,25


Technical informations:


Material:           

Plastic tube, semi-flexible:   PA 12 HL

Plastic tube, flexible:           PA 12 PHL


Standard:  DIN 73378


Material properties:   

All types of  plastic tubes (PA 12 HL, PA 12 PHL) are free of plasticisers, and resistant to light or heat-induced ageing. 


Permissible media:

Excellent resistance to oil, grease and lubricants, and to all types of fuels and chlorine-free cleaning agents and solvents.

Application for other media than those stated above, only upon request!


Permissible operating temperature: ca. – 60 °C to + 80 °C


The permissible operating pressures according to DIN 73378 are calculated by means of the following formula

       
                                                                                                                                     P =  20 · σV · s (Nenn)

                                                                                                                                             -----------------------

                                                                                                                                                      dm

s = nominal wall thickness [mm]; 

dm = da – s; 

σV = reference stress N/mm2 at 23 °C


Important advice for assembly!

Our PA12HL plastic tubes according to DIN 73378 in the dimension 6x1.5 (i.e. 6 mm outer diameter and 1.5 mm wall thickness = 3 mm inner diameter) are also referred to as poly tube 6x3. For these tubes, use of a push-in socket is not required. Assembly together with a cutting ring fitting, equal to use of our push-in fitting, is easy and straight forward.


In contrast to that, push-in sockets or reinforcement sockets must be used for PA 12 PHL polyamide tubes with wall thickness of 0.85 mm.

Please note that push-in sockets that are "lost" or "forgotten" during assembly, may result in severe problems and major damage.

As a general rule, we recommend using push-in sockets if the wall thickness of a plastic tube is </= 1.25 mm.


In our capacity as manufacturer, we would like to make our customers aware that assembly of our components for central lubrication (tubes, hoses, screw fittings, ...) must only be performed by appropriately trained and qualified personnel. 


In borderline cases, it is advisable to consult us beforehand. Have the tubes mounted only by qualified and/or accordingly trained personnel.


The warranty claims are limited to the specification of this technical data sheet. Further warranties will not be accepted. 

Download

PDF - download

technical data sheet plastic tube 100-003 / 100-003-25 unfilled

PDF - download

Product - information grease NLGI 000

PDF - download

Product - information grease NLGI 2

PDF - download

Safety data sheet for grease NLGI 000

PDF - download

Safety data sheet for grease NLGI 2

We use cookies on our website in order to offer you the best possible functionality.

Further information can be found in our privacy policy and cookies declaration.